Steps for Creating an Application Using GamryCOM

Introduction

Here are the basic steps for creating a basic application with GamryCOM. On the second page are error codes reported by GamryCOM. Please see the documentation and other example code for more information. The specifics of each step and errors vary depending on the programming environment used.

 

 Initialize Device List

1. Create an IGamryDeviceList object.
2. We recommend a three-second delay before proceeding in order to allow all of the connected Gamry Devices to initialize.
3. IGamryDeviceList.EnumSections () returns a list of available devices.

Initialize the Pstat

1. Create an IGamryPstat object.
2. Initialize the object by calling IGamryPstat.Init () and pass in the requested device’s Section.
3. Open the Pstat via IGamryPstat.Open ().

At this point, you may modify the Pstat’s settings via appropriate methods.

Initialize a Dtaq

1. Create an IGamryDtaq object appropriate for the application, such as IGamryDtaqIv, for example.
2. Initialize the Dtaq by calling the IGamryDtaq’s Init function and passing it your initialized Pstat object.
3. Register callback functions for IGamryDtaq.OnDataDone and IGamryDtaq.OnDataAvailable.

Initialize a Signal

1. Create an IGamrySignal object appropriate for the application, such as IGamrySignalArray, for example.
2. Initialize the Signal by calling the IGamrySignal’s Init () function and passing it your initialize Pstat object, as well as its other required parameters.

Set Signal

1. The Pstat needs to be notified of the Signal being used. Call the Pstat’s SetSignal () function, passing it the Signal Object that was initialized in the previous steps.

Depending on the programming environment you use, you may have to cast the initialized Signal to the more generic IGamrySignal for this step.

Acquire Data

1. Call the Dtaq’s Run function.
2. Begin acquiring data by either:

• Polling for data on a certain interval
• Using the OnDataAvailable callback mechanism
• Retrieve data from the Dtaq by calling its Cook () method, passing in the number of data points requested.

Cook() returns a two-dimensional array of data points. See the Dtaq's documentation for details on its contents.

1. Complete acquisition by:

• Waiting for the OnDataDone callback mechanism
• Calling the Dtaq’s Stop () method.

Close and clean up all objects.

 

Error Code		Description
3758096386		Device Load
3758096387		Address Invalid
3758096388		Address Used
3758096389		Device Allocation
3758096390		Device Not Responding
3758096391		IRQ Device Count
3758096392		IRQ Invalid
3758096393		IRQ Device Invalid
3758096394		Device Init
3758096395		Board Number Invalid
3758096396		Device Acq Mode
3758096397		Queue Allocation
3758096398		Device Control Mode
3758096399		Device Not Open
3758096400		Device Signal
3758096401		Device Signal Control
3758096402		Device Signal No Data
3758096403		Device Create Event
3758096404		IRQ VXD Load
3758096405		IRQ Unavailable
3758096406		IRQ Did Not Intall
3758096407		IRQ Create Thread
3758096408		IRQ Create Event
3758096409		Queue Full
3758096410		Queue Empty
3758096411		Queue Invalid
3758096412		Queue Event
3758096413		Alloc
3758096414		Event
3758096415		Invalid Key
3758096416		Invalid Classname
3758096417		Invalid Device
3758096418		Device List Load
3758096419		Register Device Notify
3758096420		Device Serial Number Not Unique
3758096421		Device Not Found
3758096422		Memory Object
3758096423		Device In Use
3758096424		Invalid Device Type
3758096425		Invalid Device Model
3758096426		Device Interface Not Found
3758096427		Device Needs Reset
3758096428		Queue Register
3758096429		List Invalid
3758096430		Device Not Authorized
3758227620		Invalid Signal Generation Parameters
2148007941		Reference Family Version Mismatch

Want a PDF version of this application note?

Please complete the following form and we will email a link to your inbox!

First Name:

Surname:

Company Name:

Email address: